同步带的分类：根据同步带齿形的不同分为梯形齿和弧形齿。弧形齿又分成圆弧齿，平顶圆弧齿和凹顶抛物线齿。（实际运用常选用公制T系列和高扭矩圆弧齿S系列。如：T5 和S5M）
Classification of synchronous belt: according to different tooth shapes of synchronous belt, it is divided into trapezoidal teeth and arc teeth. Arc tooth is divided into arc tooth, flat top arc tooth and concave top parabola tooth. (metric t series and high torque circular arc tooth s series are often selected in practical application, such as T5 and s5m)
同步轮材质：同步带轮一般由钢、铝合金、黄铜、尼龙、塑胶等材料制造，根据材质和用途的不同采用发黑、镀锌、阳极氧化、高频淬火等表面处理。（实际运行工况一般做动力传动，需要轻量化设计与减轻负载的转动惯量常选择铝合金材料+阳极氧化处理）
Synchronous pulley material: the synchronous pulley is generally made of steel, aluminum alloy, brass, nylon, plastic and other materials. According to different materials and uses, it adopts blackening, galvanizing, anodizing, high-frequency quenching and other surface treatments. (power transmission is generally used under actual operating conditions, which requires lightweight design and reducing the moment of inertia of load. Aluminum alloy material + anodizing treatment is often selected)
同步轮内孔连接方式：同步轮内孔分：圆孔（免键衬套型）、圆孔+螺纹孔、键槽孔+螺纹孔、加持型孔。
Connection mode of synchronous wheel inner hole: synchronous wheel inner hole is divided into: round hole (keyless bushing type), round hole + threaded hole, key slot hole + threaded hole and holding hole.
圆孔：与免键衬套配合使用，因为无键槽而不会降低轴的强度，并且易于定位，同心度容易保证。（实际运用中常用在丝杆固定端做动力输入或运用在对宽度需要调节的输送带上面方便调整输送带的宽度调整）

Round hole: used with keyless bushing, because there is no keyway, it will not reduce the strength of the shaft, and it is easy to locate and ensure the concentricity. (in practical application, it is often used as power input at the fixed end of the screw rod or on the conveyor belt whose width needs to be adjusted to facilitate the width adjustment of the conveyor belt)
同步轮同步带基础知识，三分钟让你快速了解同步轮同步带
The basic knowledge of synchronous wheel and synchronous belt allows you to quickly understand the synchronous wheel and synchronous belt in three minutes
圆孔+螺纹孔：通过圆孔进行定位，螺钉固定和传动扭矩，适用于轻负载。（实际工况很少使用这样情况，一般对力要求不高，轴径比较小时才做考虑，且轴上铣偏位）
Round hole + threaded hole: positioning through round hole, screw fixation and transmission torque, suitable for light load. (it is rarely used in actual working conditions. Generally, the force requirements are not high, the shaft diameter ratio is small, and the milling deviation on the shaft)
同步轮同步带基础知识，三分钟让你快速了解同步轮同步带
The basic knowledge of synchronous wheel and synchronous belt allows you to quickly understand the synchronous wheel and synchronous belt in three minutes
键槽型+螺纹孔型：由键槽来传递更大的扭矩，适用于中重负载。（选此方式）
Keyway + threaded hole: the keyway transmits greater torque, which is suitable for medium and heavy loads. (most preferred)
同步轮同步带基础知识，三分钟让你快速了解同步轮同步带
The basic knowledge of synchronous wheel and synchronous belt allows you to quickly understand the synchronous wheel and synchronous belt in three minutes
夹持型：通过螺栓连接，容易轴向定位。（一般不选用此方式）
Clamping type: through bolt connection, it is easy to locate axially. (this method is generally not used)
同步轮同步带基础知识，三分钟让你快速了解同步轮同步带
The basic knowledge of synchronous wheel and synchronous belt allows you to quickly understand the synchronous wheel and synchronous belt in three minutes
同步轮同步带的安装要求：安装时需要注意带轮轴线的平行度，各带轮的传动平面位于同一平面内，防止因为带轮偏斜而使带侧面压紧在挡圈上，造成带侧面磨损。带的张紧通过调节距或加张紧轮来实现。
Installation requirements for synchronous pulley and synchronous belt: pay attention to the parallelism of pulley axis during installation. The transmission center plane of each pulley is located in the same plane to prevent the belt side from being pressed on the retaining ring due to pulley deflection, resulting in belt side wear. The belt is tensioned by adjusting the center distance or adding tensioning wheels.
今天小编给大家呈现就是关于山东同步带的相关知识，如果您对于本文有什么疑问及问题欢迎来电咨询或者网站下边留言：http://www.huafengxiangsu.com
Today, Xiaobian presents you the relevant knowledge about Shandong synchronous belt. If you have any questions and questions about this article, please call us or leave a message at the bottom of the website: http://www.huafengxiangsu.com