输送带产品的主要原材料包括橡胶、帆布、钢丝等，使用起来还是效果挺高的，那么你知道输送带工作前后应当多注意使用以及保养的内容是什么吗？
The main raw materials of conveyor belt products include rubber, canvas, steel wire, etc., and the use effect is still very high. Do you know what should be paid more attention to the use and maintenance of conveyor belt before and after work?
避免托辊被物料覆盖而导致转动失败，防止卡与辊及胶带之间漏油，注意运动部件的润滑，但不要污染输送带；避免带载启动；胶带出现跑偏，应及时采取纠正措施；如发现胶带局部损坏，应及时修复，以免扩大；防止胶带被架子、柱子或块状材料堵塞，防止被折断和撕裂。
Avoid the rotation failure caused by the cover of the idler by materials, prevent oil leakage between the card and the roller and the belt, and pay attention to the lubrication of moving parts, but do not pollute the conveyor belt; Avoid starting with load; If the tape deviates, corrective measures shall be taken in time; In case of local damage of the adhesive tape, it shall be repaired in time to avoid expansion; Prevent the tape from being blocked by shelves, columns or block materials, and from being broken and torn.
在运输和储存过程中，输送带应保持清洁，避免阳光直射或雨雪淋湿，防止与酸、碱、油、有机溶剂等物质接触，与输送带保持距离；储存期间，库内温度应保持在-18-40度之间，相对湿度应保持在50-80%之间。
During transportation and storage, the conveyor belt shall be kept clean, avoid direct sunlight or rain and snow, prevent contact with acid, alkali, oil, organic solvent and other substances, and keep a distance from the conveyor belt; During storage, the temperature in the warehouse shall be kept between - 18-40 ℃ and the relative humidity shall be kept between 50-80%.
山东输送带储存期间，产品必须成卷放置，不得折叠。贮存期间应每季度翻动一次。不同型号规格的输送带不宜一起使用，接头更好用胶接。输送带的类型、结构和层数应根据使用条件合理选择。
During the storage of Shandong conveyor belt, the products must be placed in rolls and shall not be folded. It shall be turned once a quarter during storage. Conveyor belts of different models and specifications should not be used together, and the joints should be glued. The type, structure and number of layers of conveyor belt shall be reasonably selected according to the service conditions.
输送带的运行速度不应大于2.5m/s。对于结块大、磨损大的物料，应采用定力式卸料装置，尽量采用低速。输送机传动辊筒直径与输送带布层的关系，传动辊筒与换向辊筒的配合，支架角度的要求，应按设计规定合理选择的输送机。
The running speed of the conveyor belt shall not be greater than 2.5m/s. For materials with large agglomeration and wear, the fixed force unloading device shall be adopted, and the low speed shall be adopted as far as possible. The relationship between the diameter of the transmission roller of the conveyor and the cloth layer of the conveyor belt, the coordination between the transmission roller and the reversing roller, and the requirements of the support angle shall be reasonably selected according to the design regulations.
送料方向应与皮带运行方向一致。为了减少物料下落时对皮带的冲击，建议您使用溜槽，以减少物料的下落距离；收带部分应缩短托辊之间的距离，并使用缓冲托辊。为防止漏料，在皮带侧应使用柔软适中的挡板，以防止挡板过硬而划伤输送带的带面。
The feeding direction shall be consistent with the running direction of the belt. In order to reduce the impact of falling materials on the belt, it is recommended that you use chute to reduce the falling distance of materials; The take-up part shall shorten the distance between idlers and use buffer idlers. In order to prevent material leakage, a soft and moderate baffle shall be used on the belt side to prevent the baffle from scratching the belt surface of the conveyor belt.
That's all for the use and maintenance of the conveyor belt before and after work. If you know anything else, you can visit www.huafengxiangsu.com at any time COM and communicate with us.
联系微信