同步带是综合了带传动、链条传动和齿轮传动的优点而发展起来的新塑传动带，那么你知道同步带超过有效使用条件及过早故障的原因是什么吗？下面来了解下吧。

　　Synchronous belt is a comprehensive belt drive, chain drive and gear drive advantages and the development of the new plastic belt, then you know synchronous belt over the effective use conditions and premature failure is what? Let's take a look.

　　同步带由带齿形的一工作面与齿形带轮的齿槽啮合进行传动，其强力层是由拉伸强度高、伸长小的纤维材料或金属材料组成，以使同步带在传动过程中节线长度基本保持不变，带与带轮之间在传动过程中投有滑动，从而保证主、从动轮间呈无滑差的间步传动。

　　Synchronous belt by a working face with tooth and tooth belt wheel tooth meshing of gear, the strong layer is composed of high tensile strength, elongation of small fiber materials or metal materials, so that the synchronous belt pitch line length in the process of transmission basic remains the same, between the belt and belt wheel sliding in the transmission process, thus ensuring the main, driven wheel is no slip step transmission.

　　山东同步带超过有效使用条件的原因是什么？

　　What is the reason why shandong synchronous belt exceeds the effective use condition?

　　单一同步带或多条同步带均匀伸长，使用条件不足，用技术设计手册检查使用的条件；严重过载或传动装置系系动设计不足，重新设计；张力部件断裂，更换同步带适当安装。

　　Single synchronous belt or multiple synchronous belt uniformly extended, insufficient use conditions, with the technical design manual to check the use of conditions; Serious overload or insufficient design of transmission safety system, redesign; Tension parts broken, replace the timing belt properly installed.

　　多条同步带不均匀伸长，传动装置没有调准，重新按直线一致和松紧调准；同步带轮内有碎片，清理同步带轮；张力部间断裂或蕊线层损坏，更换所有同步带并适当安装；同步带不配合，安装能配合的同步带。

　　A number of synchronous belts are not evenly stretched, and the transmission device is not adjusted, and the alignment should be consistent and elastic again according to the straight line; There are debris in the synchronous belt pulley, clean the synchronous belt pulley; If the tension part is broken or the core line layer is damaged, replace all synchronous belts and install them properly; If the synchronous belt does not match, install a synchronous belt that can match.

　　山东同步带过早故障的原因是什么？

　　What is the cause of premature failure of Shandong synchronous belt?

　　不正确的安装皮带轮，不要在超过的扭矩数值情况下紧轴套螺丝；外来物品落入传动装置内，使用适当的防护档版；超速，保持皮带轮速度低于大值；不正确的安装皮带轮，不要用撬具将皮带装上皮带轮；严重皮带轮沟槽磨损，皮带过度张力，重新调准检查传动装置设计；砂碎片或污染，尽量清洁和防护传动装置。

　　Install the pulley incorrectly and do not tighten the bushing screws when the recommended torque value is exceeded. Foreign articles fall into the transmission device, use appropriate protective plate; Overspeed, keep the pulley speed below the maximum recommended value; Improper installation of the belt pulley, do not use a pry to install the belt pulley; Serious belt pulley groove wear, excessive belt tension, recalibration check transmission device design; Sand debris or contamination, as much as possible to clean and protect the transmission.

　　同步带超过有效使用条件及过早故障的原因便是以上相关内容了，如果您对此有什么问题没有得到有效解决的话，欢迎来网站www.huafengxiangsu.com进行相应的咨询。

　　Synchronous belt over the effective use conditions and premature failure is the cause of the above related content, if you have any problems have not been effectively solved, welcome to the website www.huafengxiangsu.com for the corresponding consultation.