大多数输送带都是由向输送带制造商解释带的参数和特的参数和特点，都是环形输送带，安装过程因连接方式而异。那么山东输送带皮带扣是如何安装的？

　　Most of the conveyor belt is explained by the conveyor belt manufacturer belt parameters and special parameters and characteristics, are circular conveyor belt, installation process varies by connection mode. So how is the belt buckle of Shandong conveyor belt installed?

　　山东输送带皮带扣是如何安装的

　　Shandong conveyor belt belt buckle is how to install

　　锁扣连接。锁连接的输送带切割尺寸后，接头通过锁连接在一起。两端的锁通过钢棒连接，拆卸方便，安装简单。因此，安装时无需拆卸辊。两侧接头对齐后，插入钢棒。

　　Latch connection. After the conveyor belt connected by the lock is cut to size, the joints are connected together by the lock. Both ends of the lock through steel rod connection, easy to disassemble, simple installation. Therefore, there is no need to remove the roll during installation. After both joints are aligned, insert the steel rod.

　　热硫化连接。热硫化连接的输送带通过调整准确的温度和压力来实现连接。连接前，皮带应进行齿工艺。生产的皮带接口可承受较高的张力，外观与皮带的其他部分基本相同。这种连接方式产生的输送带具有外观美观、整体规则、接口张力强的特点。

　　Hot curing joint. The conveyor belt connected by heat vulcanization is connected by adjusting the accurate temperature and pressure. Before connecting, the belt should be toothed. The belt interface can withstand high tension, and the appearance is basically the same as the rest of the belt. The conveyor belt produced by this connection mode has the characteristics of beautiful appearance, overall rules and strong interface tension.

　　山东输送带皮带扣注意事项？

　　Shandong belt belt buckle matters needing attention?

　　施工前，先把皮带控制开关操作手把打到“零位”锁死，并且挂牌“有人施工，严禁合闸”，设专人看。施工负责人安排人员对皮带机打扣位置范围内的杂物清理干净，确保施工退路畅通。

　　Before construction, first hit the belt control switch operator handle to “zero” to lock, and the listing “there is construction, it is forbidden to close”, set a special person to see. The person in charge of construction shall arrange the personnel to clean up the sundries within the buckle position of the belt machine to ensure the smooth construction retreat.

　　打皮带扣工作必须是在施工负责人的指导下进行施工作业施工时，施工单位必须有干部现场指挥，确保施工。

　　Belt buckle work must be carried out under the guidance of the construction person in charge of construction, construction units must have cadres on-site command, to ensure the safety of construction.

　　对更换皮带接头的工作，应先将需更换的皮带接头开到皮带机中部，把皮带放松，用两付夹板卡住皮带，卡住皮带后，用手拉葫芦进行紧带，严集用点动或开动皮带进行紧输送带。

　　For the replacement of belt joint, the belt joint to be replaced should first be opened to the middle of the belt machine, the belt is relaxed, the belt is stuck with two sets of splint, the belt is stuck, the belt is tightened with the hand hoist, and the belt is tightened with the point of movement or start.

　　山东输送带皮带扣是如何安装的？以上内容便是相关解答了，如果您还有其他方面的问题要知道的，就来我们网站www.huafengxiangsu.com进行咨询吧。

　　Shandong conveyor belt belt buckle is how to install? The above content is related to the answer, if you have other questions to know, please come to our website www.huafengxiangsu.com for consultation.